Mã sản phẩm: EnStation2

    Mô tả: Outdoor Long-Range N300 Ethernet Bridge, 2.4GHz

    Xuất xứ: Taiwan

    Bảo hành: 12 tháng

Liên hệ: 079.99999.78

Chi tiết sản phẩm

Strong 26dBm Transmit Power, 13dBi Antennas Extend Networks to 5 Miles Pt.-to-Pt.
11n Speeds to 300Mbps on 2.4GHz; to 90Mbps at ½ Mile
PoE Port & Injector Extends Power to Unwired Areas; Connect Remote IP Cameras or APS via 2nd Port
Narrow-Focused Wireless Beam Reduces Long-Range Interference
360° 3-Axis Pivoting Arm Locks for Precise Alignment; Wall & Pole Mount-Ready
Rugged IP55-Rated Weatherproof Case Defies Harsh Climates


EnStation2 is a 2.4 GHz High-Powered, Long-Distance Wireless N300 Outdoor AP/Client Bridge with a high-gain 13 dBi dual-polarization internal directional antenna ideal for Point-to-Point deployments up to 4 miles. It includes two (2) Fast Ethernet ports and is housed in an IP55-rated waterproof housing to maintain robust performance even in harsh environments. Its a smart solution for streaming video data for IP Cameras monitoring parking lots and it includes an additional Fast Ethernet Port (LAN 2) to connect a camera for this type of application.

Going The Distance. EnGenius EnStations are Outdoor Wireless Access Points that feature high 26 dBm output power and high receive sensitivity coupled with embedded high-gain directional antennas that emit a narrow signal beam to deliver robust and stable connectivity over extremely long distances — up to 4 miles in clear line-of-sight point-to-point deployments! EnStations, therefore, are ideal for:

• extending networks in large campus venues;
• over extensive acreage in industrial, farming or ranching properties;
• in massive indoor structures like arenas, shopping malls, warehouses, convention centers;
• connecting to digital signage;
• or even in more urban environments where there is clear line-of-sight between the EnStation and another Access Point; or between two EnStation units of the same frequency band.

WISP Scenarios. EnStations can be used in Client Bridge mode and pointed to a Wireless Internet Service Provider’s base station making them ideal CPE (Customer Premise Equipment) that can generate recurring revenue for Internet providers. The compact form factor of EnStation also make it acceptable to many homeowners association because they are barely noticeable and unobtrusive additions to home exteriors and usually within the guidelines of a planned community’s architectural standards.


Technical Specifications


RF: 2.4 GHz Frequency Band
Standard: IEEE 802.11b/g/n 
Radio I: 11b/g/n: 2.412~2.484 GHz
Data Rate: Up to 300 Mbps in 2.4 GHz
Memory: 128MB
Flash Memory: 16MB
Transmit Power: 
Up to 26 dBm
Up to 400 mW
Radio Chains/Spatial Streams – 3x3:3
Supported Radio Technologies:
802.11b: Direct-sequence spread-spectrum (DSSS)
802.11n: Orthological Frequency-Division Multiplexing (OFDM)
802.11n: With 5/10/20/40 MHz Channel Width
Supported Modulation Types:
802.11b: BPSK QPSK, CCK
802.11n: BPSK, QPSK, 16-QAM, 64-QAM
Supported Data Rates (Mbps): 
802.11b: 1, 2, 5.5, 11
802.11g: 6, 9, 12, 18, 36, 48, 54
802.11n: 6.5~300 (MCS0 to MCS15)


Physical Interface
Two (2) 10/100 BASE-T Ethernet Ports
One (1) Port supports 24V Proprietary PoE Input
One (1) Port supports extension of an Internet signal
Reset Button
LED Signal


One (1) Internal High-Gain Directional Antenna
13 dBi GHz Antenna
Azimuth Beam Width (Horizontal): 18°
Elevation Beam Width (Vertical): 30° 
Point-to-Point Transmission for Long Range Distances
2.4 GHz (Point 1)
Peak Antenna Gain: 13 dBi
Polarization: Linear
Horizontal Beam Width: 67° 
Elevation Beam-Width: 33°
VSWR: 1:2.0
2.4 GHz (Point 2)
Peak Antenna Gain: 13 dBi
Polarization: Linear
Horizontal Beam Width: 61° 
Elevation Beam-Width: 35°
VSWR: 1:2.0


Power Requirements 
Power Source (PoE Injector):
24V/.6A Proprietary Compliant Source
Active Ethernet (Power over Ethernet, PoE)
Power Consumption: 7.2 W
Peak Power Consumption: Up to 34 W




Auto Channel Selection
Settings varies by Regulatory Domains


Operation Modes 
Access Point, Client Bridge, WDS Bridge


IP (check validity and DHCP server IP range) MAC


Supports Four (4) SSIDs


VLAN Tagging
Independent VLAN settings cab be enabled/disabled
Any packet that enters the device without a VLAN tag will have a VLAN tag inserted via a PVID (Ethernet Port VID)
VLAN Pass-through
VLAN Pass-through over WDS Bridge


V1/v2c/v3 Support
MIB I/II and Private MIB


Compliant with IEEE 802.11e Standard


Other Management Features
Save Configurations as Default
Saves the customized configuration as the default value for different customer demands
Client Traffic Status
Reports various information in a timely manner as required by the administrator